Home > Electrical > Generator Parts & Accessories >

RV Automations Alert Command Auto Generator Start & Temperature Monitoring System With Text Alerts
RV Automations Alert Command Auto Generator Start & Temperature Monitoring System
RV Automations Alert Command Auto Generator Start & Temperature Monitoring System


 
Price: $396.95
MFG P/N: ALERTCOMMAND
MFG: RV Automations


Quantity in Stock :8


Availability: In Stock
Product Code: ALERTCOMMAND
Qty:

Description Instructions
 
The RV Automations Alert Command is an auto generator start system that monitors your shore power and auto-starts your generator in the event of a power outage. Also m onitors the inside temperature of your RV with an optional temperature monitoring sensor.
  • Important Note: Text alerts require a subscription of 9.99 per month. Alerts notify you of lost/restored shore power, or when your generator is automatically turned on or shut off, click here
  • Monitors shore power directly from a 50/30-amp pedestal. No modifying required to your inverter panel or transfer switch.
  • 3 operating modes monitor when you are connected to shore power, dry camping, and also works in shore power mode if you don’t have a generator installed.
  • Modes:
    • Shore Power Mode
      • Monitors your RV site shore power.
      • If shore power is lost: texts your phone notifying you that shore power was lost, and then automatically turns on your generator, sending another text to confirm your generator started.
      • When shore power is restored: texts your phone notifying you shore power has been restored, and then automatically shuts off your generator, sending another text to confirm your generator was turned off.
    • Dry Camping Mode
      • Monitors your generator status, and sends text alerts when your generator starts and when it has stopped running.
      • Note: Works parallel with Class A coaches with a factory-installed AGS system.
    • Shore Power / No Gen Mode
      • Monitors your shore power and texts your phone when shore power is lost and when shore power is restored.
      • Only requires a simple 4-wire connection.
    • Temperature Monitoring
      • Monitors the inside temperature of your RV with an optional temperature monitoring sensor (sold separately), see the 3-foot sensor or the 20-foot sensor
      • Pre-programmed to text you when the inside temperature of your RV reaches 85 degrees, or when the inside temperature drops to 45 degrees F
      • Text alerts also sent when the temperature falls below 85 degrees or rises above 45 degrees F.
  • Pre-Programmed Text Alerts:
    • Alert Command: Enabled and Connected
    • Alert Command: Shore Power Lost
    • Alert Command: Shore Power Restored and Generator Off
    • Alert Command: Generator Started and Running
    • Alert Command: Generator Turned Off
    • Alert Command: Inside temperature is over 85 degrees
    • Alert Command: Inside temperature is below 85 degrees
    • Alert Command: Inside temperature is below 45 degrees
    • Alert Command: Inside temperature is above 45 degrees
  • Compatible with any cellular network (Verizon, T-Mobile, AT&T, etc).
  • No WiFi required.
  • May be DIY installed, or installed by a dealer. No complex wiring involved. Includes heavy-duty connectors and posi-taps for easy wire splicing.
  • 8-wire connection for full operation, or 4-wire for only monitoring shore power (no generator installed).
  • Tested on most Onan RV generators.
  • Works with generators that have the following 4 wires: start wire, stop wire, run wire, and ground wire.
  • Shore power is monitored on the 120V side of your transfer switch, allowing Alert Command to monitor shore power right from the source (power pedestal).
  • Ready to install right out of the box. No hard-to-read programming required for setup.
  • May be installed inside your RV, generator compartment, or near your transfer switch.
  • Runs parallel with any factory-installed auto generator start system, or in conjunction with any smart RV monitoring applications.
  • Rugged compact, durable design.
  • What is required for installation: (4) 18-gauge wires for generator connection, (1) pair of 14-gauge wires to connect to battery and ground, (1) pair of 14-gauge wire to connect from the transfer switch to Alert Command, (4) screws to mount Alert Command.
  • Tools needed to install: Wire stripper, screwdriver (Philips or Flathead) small zip ties, or electoral tape.
  • Enclosure Dimensions: 7-1/2” wide x 4-3/4” width x 1-1/2” height.
  • Weight: 3 lbs.
  • Includes (1) alert command unit, (2) heavy-duty screw connectors, (1) 120V inline fuse, (4) posi-taps.
  • Limited 3-Year Manufacturer Warranty.

RV Automations Alert Command Auto Generator Start & Temperature Monitoring System



ACCESSORIES
RV Automations Temperature Sensor - 20 Ft
Price: $45.50
RV Automations Temperature Sensor - 20 Ft