Replacement sway control bracket kit for Fastway e2 weight distribution hitches rated from 6,000 to 12,000 lbs GTW. Designed for e2 round bar and trunnion bar systems and compatible with 3", 4", 5", and 6" trailer frames.
The Fastway 93-01-5660 e2 Sway Control Bracket Kit is a replacement bracket assembly for Fastway e2 weight distribution hitch systems. This bracket mounts to the trailer frame and provides the L-bracket attachment point where the e2 spring arm rests during towing.
The bracket is part of the Fastway e2 hitch setup that helps distribute weight and reduce trailer sway. It is designed for 6K, 8K, 10K, and 12K Fastway e2 hitches and can be used with both round bar and trunnion bar e2 systems.
Replacement sway control bracket kit for Fastway e2 weight distribution hitches
Designed for Fastway e2 hitches rated from 6,000 to 12,000 lbs GTW
Compatible with 3", 4", 5", and 6" trailer frames
Works with compatible Fastway e2 round bar and trunnion bar hitch systems
A complete Fastway e2 hitch setup uses one sway control bracket assembly on each side of the trailer frame. This listing is for one bracket kit. Order two kits if replacing both trailer-frame bracket assemblies. This bracket kit is for Fastway e2 6K-12K weight distribution hitches. It is not for original Equal-i-zer 4-Point Sway Control hitches unless specifically cross-referenced by the manufacturer.
Replace the bracket kit if the original bracket assembly is missing, bent, cracked, heavily corroded, worn, or no longer holds the spring arm securely. Visible bracket damage: Do not tow with a cracked, bent, distorted, or loose L-bracket assembly. Missing hardware: Replace the bracket hardware if the original parts are incomplete, stripped, worn, or corroded. Used hitch setup: This kit is helpful when setting up a used Fastway e2 hitch that is missing one trailer-frame bracket assembly. Frame-size change: Confirm the bracket is correctly configured for the trailer frame height before towing.
Installation Steps: 1. Park Safely: Park the tow vehicle and trailer on level ground before servicing the hitch 2. Confirm Hitch Rating: Verify the hitch is a Fastway e2 system rated between 6,000 and 12,000 lbs GTW 3. Confirm Frame Size: Make sure the trailer frame is 3", 4", 5", or 6" tall 4. Position the Bracket: Install the bracket assembly on the trailer frame at the correct distance from the coupler according to the Fastway e2 manual 5. Secure the Bracket: Tighten the bracket hardware evenly and torque according to the manual 6. Install Spring Arm: Place the e2 spring arm onto the L-bracket and retain it with the proper L-pin and clip 7. Final Safety Check: Confirm both trailer-frame bracket assemblies, spring arms, L-pins, and clips are secure before towing Always follow the Fastway e2 owner's manual for your specific hitch model. Do not tow with missing, damaged, modified, loose, or improperly installed weight distribution hitch hardware.
• (1) Inside Link Plate • (1) Outside Pocketed Link Plate • (1) L-Bracket • (1) L-Pin and Clip • (2) 7/16" x 3-1/2" Bolts • (2) 7/16" Split-Ring Washers • (2) 7/16" Nuts • (2) 3/8" x 1-1/2" Stud Bolts • (2) 3/8" Nylock Nuts
Fastway Trailer Products / Progress Mfg.: Website: fastwaytrailer.com/contact-us Fastway is manufactured by Progress Mfg., the same company behind Fastway and Equal-i-zer towing products.
Use this guide to confirm whether Fastway 93-01-5660 is the correct replacement bracket kit for the hitch and trailer frame.