Replacement Snap L-Pin for Equal-i-zer weight distribution hitches rated 6,000 lb through 16,000 lb. The Snap L-Pin secures the spring arm / weight distribution bar to the L-bracket on the trailer frame and uses a clip-less snap-down design for quick setup. Single pin only — order two if replacing both sides of the hitch.
The Equal-i-zer 90-03-9230 Snap L-Pin is a genuine replacement retaining pin for Equal-i-zer weight distribution hitch systems. It is used at the trailer-frame L-bracket to hold the spring arm / weight distribution bar securely in place while towing.
The Snap L-Pin replaces the older separate L-pin and clip style with a convenient one-piece, clip-less snap-down design. This helps make hitching faster and reduces the chance of losing a small retaining clip during setup, storage, or travel. This listing is for one Snap L-Pin only; most Equal-i-zer hitch systems use one pin on each side, so two are needed to replace both L-bracket pins.
Factory replacement Snap L-Pin used with Equal-i-zer weight distribution hitch L-brackets
Designed for Equal-i-zer weight distribution hitches rated from 6,000 lb through 16,000 lb
Integrated snap-down style eliminates the separate retaining clip used on older L-pin designs
Factory-style replacement size for securing the spring arm at the trailer L-bracket
This part is a Snap L-Pin for Equal-i-zer weight distribution hitches. It is not a leveling jack handle, jack pin, stabilizer jack part, or general RV leveling system component. Compatibility note: Equal-i-zer lists 90-03-9230 as the Snap L-Pin for 6K, 10K, 12K, 14K, and 16K hitch systems. The 4K Equal-i-zer hitch uses a different L-pin, part number 90-03-9460, along with a separate L-pin clip.
Replace the Snap L-Pin if the original pin is missing, bent, cracked, heavily worn, corroded, or no longer snaps securely over the spring arm. Missing Pin: Do not tow without the spring arm properly retained at the L-bracket. Bent or Damaged Pin: A distorted pin may not seat correctly and may interfere with proper spring arm retention. Weak Snap Action: Replace the pin if the snap-down portion no longer closes or holds securely. Worn Contact Area: Replace if the pin is wearing heavily where it contacts the spring arm or L-bracket.
Installation Steps: 1. Park Safely: Park the tow vehicle and trailer on level ground and make sure the trailer is secured before working around the hitch 2. Position the Spring Arm: Place the Equal-i-zer spring arm on the trailer-frame L-bracket according to your hitch manual 3. Insert the Snap L-Pin: Slide the Snap L-Pin into position so it captures the spring arm at the L-bracket 4. Snap Closed: Rotate or snap the integrated retaining portion down until the pin is fully secured 5. Repeat if Needed: Install the second Snap L-Pin on the opposite side if replacing both L-bracket pins 6. Inspect Before Travel: Confirm both spring arms are seated on the L-brackets and both Snap L-Pins are fully closed before towing Always follow the Equal-i-zer owner's manual for your specific hitch model. Do not tow with missing, damaged, modified, or improperly secured pin hardware.
In The Package: • (1) Snap L-Pin Not Included: • Second Snap L-Pin • L-bracket • Link plates • Spring arm • Hitch head • Shank • Socket pin or socket pin clip • Snap-up handle or hook • Hitch ball
Equal-i-zer Hitch / Progress Mfg.: Website: equalizerhitch.com/contact-us Made in the USA Equal-i-zer is manufactured by Progress Mfg., the same company behind Equal-i-zer and Fastway towing products.
Use this guide to distinguish the 90-03-9230 Snap L-Pin from other Equal-i-zer pin and hitching hardware.
Need to replace both L-bracket pins? Order two 90-03-9230 Snap L-Pins or choose an Equal-i-zer two-pack / double spare pin option where available.