Home > Jacks & Levelers > Levelers >

Lippert 165253 Jack Foot Pad for LCI V2 3500 lb Power Tongue Jack and Sidewinder -- Zinc-Coated Steel

Lippert 165253 zinc-coated steel jack foot pad for LCI V2 3500 lb power tongue jack and Sidewinder, 5-1/2 inch wide footplate
Lippert Jack Foot Pad For LCI Power Tongue Jack
 
Alternative Views:


List Price: $38.19
: $31.49
You save $6.70!
Part Number: 165253
Manufacturer: Lippert

Quantity in Stock :38

Availability: In Stock
Qty:

 
Lippert Part 165253 Zinc-Coated Steel Lippert 165253 Jack Foot Pad for LCI Power Tongue Jack and Sidewinder

Stop your tongue jack from sinking into soft ground, gravel, or grass. The Lippert 165253 is a direct-replacement steel foot pad engineered for the LCI next-generation V2 3500 lb. power tongue jack as well as LCI Smart and manual Sidewinder tongue jacks. A zinc coating keeps rust and corrosion at bay through seasons of outdoor exposure.

A Solid Foundation for Your Tongue Jack

Every time you park your trailer, the tongue jack bears the full downward load of your hitch weight -- often on pavement, gravel, grass, or soft dirt that isn't perfectly firm. Without an adequate foot pad, the jack tube can dig in, tip, or transfer uneven stress to the jack mechanism itself. The Lippert 165253 gives that tube a wide, stable base and keeps the load distributed across the ground surface.

At just 1.3 lbs., it adds almost nothing to your setup weight, and the 5-1/2" wide footplate provides meaningful ground contact for a jack rated to 3,500 lbs. The 2" inner tube diameter matches the LCI power tongue jack and Sidewinder leg tube for a secure, rattle-free fit secured by a clevis pin (not included -- reuse your existing hardware or source separately).

Zinc-Coated Steel

Resists rust and corrosion through rain, mud, and road spray. Tough enough for full-time and seasonal use.

Wide 5-1/2" Footplate

Distributes jack load across soft ground -- grass, gravel, dirt -- reducing sinking and instability at the hitch end.

2" Inner Tube Diameter

Matches LCI V2 power tongue jack and Sidewinder jack leg tubes for a direct, no-adapter fit.

OEM Replacement Part

Genuine Lippert component. Replaces worn, bent, or missing foot pads on compatible LCI jack models.

Fitment and Compatibility

The 165253 foot pad is confirmed to fit the following LCI tongue jack families:

  • LCI next-generation V2 3500 lb. power tongue jack
  • LCI Smart tongue jack (Sidewinder series)
  • LCI manual Sidewinder tongue jack

If you are unsure whether your jack is a V2 or Sidewinder model, check the label on the jack body or compare your existing foot pad's inner tube diameter -- this pad requires a 2" leg tube. Non-LCI or older-generation jacks may not share the same leg diameter or pin hole geometry.

Direct Fit -- No Modifications Needed: Slides onto the existing jack leg tube and is retained by your existing clevis pin and cotter pin. No drilling, welding, or fabrication required.

Installation Notes

Swapping the foot pad is a straightforward job with basic hand tools:

  • Extend the jack to expose the lower leg tube and existing foot pad.
  • Remove the cotter pin and clevis pin retaining the old foot pad.
  • Slide the old pad off and the new 165253 pad onto the leg tube.
  • Reinstall the clevis pin and cotter pin through the existing pin hole (1-5/8" from top of footplate to pin hole center).
  • Verify the pad seats flush and does not rock before lowering the trailer onto it.
Pins Not Included: The clevis pin and cotter pin are NOT included with this foot pad. Reuse your existing hardware if it is in good condition, or source replacements separately. Do not operate the tongue jack without the retaining pin properly installed.
Tip for Soft Ground: Even with this foot pad, consider placing a jack pad block or piece of lumber under the footplate on very soft or wet soil to further increase the bearing surface and prevent sinking under full hitch weight.

What Is Included

  • (1) Lippert 165253 replacement jack foot pad

Clevis pin and cotter pin are NOT included. Existing jack hardware should be reused or sourced separately.

Maintenance Tip: Inspect the foot pad and retaining pins at the start of each camping season. Look for cracks, bent steel, worn pin holes, or rust that has compromised the zinc coating. A bent or cracked foot pad can shift under load and destabilize your parked trailer.

Product Specifications

Lippert Part Number165253
Vendor Part Number71-5528
UPC848150057648
ManufacturerLippert (LCI)
Weight1.3 lbs.

Dimensions

Footplate Width5-1/2 inches
Inner Tube Diameter2 inches
Top of Footplate to Pin Hole Center1-5/8 inches

Materials and Finish

MaterialSteel
FinishZinc coating (rust and corrosion resistant)

Compatibility

LCI V2 Power Tongue Jack3500 lb. capacity, next-generation series
LCI Smart Sidewinder Tongue JackCompatible
LCI Manual Sidewinder Tongue JackCompatible
Required Leg Tube Diameter2 inches

What Is Included

Foot Pad1x Lippert 165253 jack foot pad
Clevis PinNot included -- reuse existing or source separately
Cotter PinNot included -- reuse existing or source separately

Warranty

WarrantyLimited 1-Year Manufacturer Warranty (Lippert)
Important Information
  • Clevis pin and cotter pin are NOT included. The foot pad cannot be safely used without these retaining components. Source replacements or reuse existing hardware.
  • Confirm your tongue jack leg tube measures 2 inches in inner diameter before ordering. This pad will not fit smaller or larger tube sizes.
  • This pad is rated for use with jacks up to 3,500 lbs. capacity. Do not use on higher-capacity jacks or other jack types not listed in the compatibility section.
  • Inspect the foot pad and retaining pins for wear, cracks, or corrosion before each use. A damaged foot pad can shift under load and create an unstable and unsafe condition.
  • Even with the foot pad installed, use additional ground support (boards, jack pads) on extremely soft or waterlogged ground.


Browse for more RV Accessories in the same category as this item:

Jacks & Levelers > Levelers
Jacks & Levelers


$3.94
$10.24