Permanent recycled rubber jack pad kit for compatible Class A motorhomes with EQ Systems® leveling jacks using two 10" octagonal jack feet and two 12" round jack feet.
The SnapPad EQ812SP4 Grand Octagon 4-pack is designed for a common EQ Systems® leveling setup found on Class A motorhomes: two 10" octagonal jack feet and two 12" round jack feet. Once installed, the pads stay attached to the leveling jack feet, eliminating the need to place loose pads or blocks under the jacks during normal setup.
These permanent rubber jack pads increase the landing footprint, help dampen vibration, improve grip on a variety of surfaces, and help protect both the metal jack feet and the parking surface below. This kit is commonly associated with Class A motorhomes from brands such as Entegra®, Forest River®, Newmar®, and Thor® when equipped with the correct EQ jack foot combination.
Snap-on pads stay attached to compatible jack feet after installation
Includes pads for two 10" octagonal feet and two 12" round feet
Designed for compatible Class A motorhomes with EQ Systems® jacks
Helps protect jack feet and parking surfaces from damage and wear
SnapPad EQ812SP4 is not universal for every EQ leveling system. This kit is intended for Class A motorhomes with two 10" octagonal jack feet and two 12" round jack feet. Always measure the actual jack feet and confirm their shape before ordering. Check clearance before installation. SnapPad recommends verifying approximately 2" of side clearance and 3/4" of top-edge clearance around the jack feet to avoid interference with tires, suspension blocks, brake components, or nearby RV structure.
Before Starting: Confirm the leveling system is compatible and measure all jack feet. This kit is for a mixed setup with two 10" octagonal feet and two 12" round feet. Basic Installation Steps: 1. Measure Jack Feet: Confirm two jack feet are 10" octagonal and two jack feet are 12" round. 2. Check Clearance: Verify enough side and top-edge clearance around each jack foot before installing pads. 3. Inspect Jack Feet: Check for bent metal, heavy rust, damage, or unusual jack foot shape that may affect fit. 4. Clean the Feet: Remove dirt, gravel, grease, or loose debris from the jack feet before installation. 5. Position the Pad: Align the correct SnapPad with the matching jack foot shape and size. 6. Lower the Jack: Use the leveling system to press the jack foot into the pad until it fully seats. 7. Confirm Attachment: Visually inspect that each pad is fully seated and locked around the jack foot. 8. Test Clearance: Retract the jacks and confirm the installed pads do not interfere with nearby components.
Package Contents: • 2 SnapPad EQ Octagon pads for compatible 10" octagonal jack feet • 2 SnapPad EQ Grand pads for compatible 12" round jack feet NOT Included — May Also Need: • Leveling jacks or jack feet • Separate leveling blocks or base pads • Wheel chocks • Replacement jack foot hardware • Additional SnapPads for different jack foot sizes or shapes This listing is for the 4-pack SnapPad EQ Grand Octagon kit only. Verify jack foot size, jack foot shape, leveling system, and clearance before ordering.
To confirm compatibility before ordering, have the following ready: • RV make, model, and year • Leveling system brand/model, if known • Photos of all jack feet from below • Measurements of each jack foot • Confirmation of jack foot shape: octagonal or round • Clearance around each jack foot near tires, suspension, brake components, and frame areas Why this matters: SnapPads are selected by jack foot shape, jack foot size, and leveling system. Even on compatible brands, jack foot sizes can vary by model year, chassis, and leveling system configuration.
Match SnapPad EQ812SP4 by leveling system, jack foot shape, jack foot size, and clearance. RV brand alone is not enough to confirm fitment.
If a SnapPad does not seat correctly or clearance is tight, stop and recheck jack foot measurements, pad model, installation orientation, and nearby component clearance before operating the leveling system.