Direct-fit OE upgrade rear shock for Sprinter 3500 and 3500XD single rear wheel (SRW) vans and Class C motorhomes. 46mm monotube nitrogen gas design. Stock height. No hardware included. Made in the USA.
The Bilstein 24-167161 B6 4600 Series Rear Shock Absorber is a direct-fit OE upgrade engineered for the Mercedes-Benz Sprinter 3500 platform — covering Dodge-badged, Mercedes-Benz-badged, and Freightliner-badged versions of the same van chassis. Whether you're running a high-roof cargo van, a passenger shuttle, an upfitted work van, or a Class C motorhome on the Sprinter 3500 chassis, this shock is tuned to handle the rear axle loads these vans are built for — without the vague, floaty ride of worn OEM shocks.
The Sprinter 3500's rear suspension is constantly managing the weight of payloads, passengers, upfitter builds, or motorhome bodies — and the 4600 series is precisely valved for that duty cycle. The result is improved rear stability under load, better control during lane changes, and a more settled ride that reduces driver fatigue on long runs.
Eyelet upper and lower mounts — bolt-on rear shock replacement at stock height using OEM mounting hardware
Fade-free rear damping under sustained commercial van and Class C motorhome loads — consistent performance mile after mile
Increases rear suspension carrying capacity for cargo hauling, passenger transport, and Class C motorhome applications
Designed, engineered, and manufactured in the USA. Backed by Bilstein's limited lifetime warranty for the original purchaser
The 24-167161 is designed exclusively for Sprinter 3500 and 3500XD models with single rear wheel (SRW) configuration. For Dual Rear Wheel (DRW) Sprinter 3500 models, the correct part is Bilstein 24-177702. Installing a SRW shock on a DRW chassis will result in improper fitment and may compromise vehicle safety. Check your rear axle configuration before ordering. DRW models have two tires side-by-side on each rear corner; SRW models have one tire per rear corner.
Hardware Not Included: Mounting hardware is not included — this shock uses your existing OEM mounting hardware. Sold Individually: One shock absorber per package. Order qty 2 for a complete rear axle replacement. Stock Height Only: The B6 4600 Series is for stock-height applications only. Verify Your Brand & Year: The Sprinter 3500 was sold under three brand names (Dodge, Freightliner, Mercedes-Benz) with different model year spans for each. Verify your vehicle brand and year matches the fitment table below before ordering.
In The Box (Qty: 1 Shock Absorber): • Bilstein 24-167161 Rear Shock Absorber • Blue Protective Boot • Black Rubber Bushings NOT Included: • Mounting Hardware (uses existing OEM hardware) • Dust Shield • Second shock (sold individually — order qty 2 for a complete rear pair)
24-177702 — Rear B6 4600 for Sprinter 3500 Dual Rear Wheel (DRW) 24-223911 — Rear B6 4600 for Sprinter 2500 (2007–2018) 22-249326 — Front B6 strut for Sprinter 2500/3500 (2007–2018) Always confirm SRW vs. DRW rear axle configuration before ordering rear shocks for the Sprinter 3500.
Bilstein Official Product Page Bilstein Technical Support: Website: www.bilstein.com Warranty: Limited Lifetime for original purchaser — B6 4600 series gas pressure shocks. Proof of purchase required. See full terms at Bilstein's website.
The 24-167161 fits the following Sprinter 3500 models with single rear wheel (SRW) configuration at stock ride height. Sold individually — order two for a complete rear replacement. The Sprinter 3500 was sold under three brand names with different year spans; verify your brand and year before ordering.
⚠️ Fitment cross-referenced across Amazon, ShockWarehouse, LM Performance, and SuperSteer Parts. This shock is for single rear wheel (SRW) Sprinter 3500 models only. For dual rear wheel (DRW) models, order Bilstein 24-177702. Always verify your rear axle configuration before ordering.