Full-motion RV TV wall mount with 17" of extension, 360° swivel, ±8° forward/backward tilt, and ±5° side-to-side tilt for dialing in the perfect viewing angle. A spring latch holds the mount securely in the closed position while traveling — no rattling or shifting on the road. The back plate mounts to the wall separately from the arm assembly for straightforward single-person installation. Supports TVs up to 50 lbs with VESA patterns up to 200 x 200mm. Made in the USA by MORryde.
The MORryde TV1-122H is a full-motion locking TV wall mount engineered specifically for the demands of RV life — where the same mount that holds your TV rock-steady on the road needs to extend, swivel, and tilt freely the moment you're set up at a campsite. The TV1-122H addresses both requirements directly. When you're ready to watch, the arm extends a full 17 inches from the wall and rotates through a 360° swivel range, letting you position the TV toward any seating area. Fine-tuning is handled by ±8° of forward/backward tilt and ±5° of side-to-side tilt — enough adjustment to eliminate glare and level the picture even when parked on a slight grade.
When it's time to travel, the arm folds back against the wall and the spring latch locks it in the closed position automatically. No tightening knobs, no bungee cords, no separate tie-downs — the latch engages when the arm is returned to the folded position and keeps it there through road vibration and movement. In the closed position, the mount has a profile of just 2.625" deep, keeping the TV tight to the wall and out of the way during transit.
Installation is simplified by the two-piece back plate design: the back plate mounts to the wall independently, then the arm assembly attaches to it — allowing one person to secure the wall plate at the correct height and position before dealing with the weight of the TV and arm. With a 50 lb weight capacity and support for VESA mounting patterns up to 200 x 200mm, the TV1-122H fits most flat-screen TVs commonly used in RV applications.
Spring latch automatically holds the mount in the closed position during travel — no knobs to tighten or tie-downs needed; keeps the TV secure through road vibration and movement
17 inches of total arm extension brings the TV closer for comfortable viewing; full 360° swivel rotates the TV toward any seating position or viewing angle in the RV
±8° forward/backward tilt and ±5° side-to-side tilt fine-tune the viewing angle to eliminate glare and level the picture — useful even when parked on uneven ground
Back plate mounts to the wall independently before the arm assembly attaches — simplifies installation and allows proper wall positioning without managing the full arm and TV weight simultaneously
Weight Capacity: The TV1-122H supports TVs up to 50 lbs. Always verify your TV's weight before purchasing. The weight of the TV and any accessories mounted to the arm must not exceed this limit. VESA Pattern: Compatible with VESA mounting patterns up to 200mm x 200mm. Verify the VESA hole pattern on the back of your TV before ordering. VESA patterns larger than 200 x 200mm are not compatible with this mount. Wall Structure: Mount must be installed into structural wall studs or appropriate wall reinforcement rated to support the combined weight of the mount and TV. MORryde is responsible for the design and manufacture of the product — the owner is responsible for ensuring the mounting surface is adequate for the installation.
Part Number: TV1-122H Brand: MORryde — Elkhart, Indiana Best For: • RV living room, bedroom, or kitchen TV installations where both travel security and flexible viewing positioning are needed • Applications where the TV is watched from multiple seating positions — the 360° swivel covers the full room • RVs with slightly uneven parking situations — the tilt range corrects for minor grade without adjusting the TV's wall mounting position Closed Position: 14.85″W × 9.75″H × 2.625″D — compact wall profile for travel Open Position: 9.5″W × 9.75″H × 17″D — full extension for viewing Installation Note: Install the back plate to the wall first, then attach the arm assembly. Refer to the included MORryde TV1-122H installation instructions for complete hardware and mounting guidance.
Before You Begin: Verify your TV's weight (50 lb max) and VESA hole pattern (200 x 200mm max). Identify structural wall studs or appropriate reinforced mounting surface rated for the combined weight of the mount and TV. Refer to the included MORryde TV1-122H installation instructions for complete hardware requirements. Installation Steps: 1. Mount the Back Plate: Secure the back plate to the wall studs or reinforced surface at the desired height — this step is done independently of the arm assembly, simplifying positioning 2. Attach Arm Assembly: Connect the arm assembly to the installed back plate per the instruction sheet 3. Mount TV to VESA Plate: Attach the VESA mounting hardware to your TV using the appropriate bolt pattern (up to 200 x 200mm) 4. Connect TV to Arm: Hang or secure the TV/VESA plate to the arm assembly 5. Adjust Tilt: Set the forward/backward tilt (±8°) and side-to-side tilt (±5°) for your preferred viewing angle 6. Test Spring Latch: Fold the arm to the closed position and confirm the spring latch engages securely — verify it holds firmly before traveling
Included: • One (1) MORryde TV1-122H Locking TV Wall Mount • Back plate (mounts to wall separately) • Arm assembly with spring latch • VESA mounting hardware (up to 200 x 200mm) • MORryde installation instruction sheet Required for Installation (Not Included): • Drill and appropriate drill bits • Stud finder • Level • Fasteners appropriate for your wall structure (lag screws into studs or appropriate anchors for reinforced wall surfaces)
Key specifications and dimensions in the two operating positions — closed for travel, open for viewing.
The spring latch engages automatically when the arm is folded to the closed position — no manual locking step required before travel. The back plate installs to the wall separately from the arm assembly for simplified single-person installation. Made in the USA by MORryde, Elkhart, Indiana.