Home > Carriers & Haulers > Bike Carriers >

Let's Go Aero B02141 V-Lectric Fat eBike Wheel Cradle Kit -- Fits Tires 2.75" to 4", 60 lb Limit

Let's Go Aero B02141 V-Lectric Fat eBike Wheel Cradle Kit with BlockHead quick-release cradles and rubber straps for fat tire electric bikes
Let's Go Aero V-Lectric Fat eBike Wheel Cradle Kit
 
: $123.00
Part Number: B02141
Manufacturer: Let's Go Aero

Quantity in Stock :12

Free Shipping
Availability: In Stock
Qty:

 
Let's Go AeroPart B02141Fits Tires 2.75" - 4"V-Lectric Fat eBike Wheel Cradle Kit -- Upfit Your Carrier for Fat Tire Electric Bikes

The Let's Go Aero B02141 is a complete wheel cradle kit that upgrades V-Lectric eBike carriers to properly support fat tire electric bikes. It also serves as a fat bike cradle upgrade for many other Let's Go Aero V-Rack models rated for non-eBikes. If you're running wide tires on a heavy electric bike, this kit gives you the cradle geometry and strap hardware to transport it securely.

BlockHead Quick-Release Cradles Built for Fat Tires and Heavy eBikes

Standard bike rack cradles are designed around narrow road and mountain bike tires. Fat tire eBikes -- with tires often 3 to 4 inches wide and total bike weights well above 50 lbs -- require cradles that can physically accept the tire and hold it without flex. The B02141 addresses both problems in one kit.

The kit ships with two Upper Wheel Cradle assemblies and two Lower Wheel Cradle assemblies, giving you full front-and-rear wheel support for a single fat eBike. Each cradle uses Let's Go Aero's BlockHead quick-release design, which slides and locks onto V-wing support arms without tools. Cradle pins are reversible, so you can flip them to fine-tune the fit for different wheel diameters quickly at the trailhead or campsite.

BlockHead Quick-Release

Button-trigger quick-release on each cradle assembly allows tool-free installation, removal, and position adjustment on V-wing support arms in seconds.

Reversible Cradle Pins

Pins flip to two positions to accommodate different wheel sizes, giving you a precise fit across a range of fat tire bike configurations.

12-Inch Rubber Straps

Four durable 12 in. rubber straps with pull tabs and pre-punched hole locations secure tires with a comfortable tension fit -- no ratchets to over-tighten or hardware to lose.

Wide Tire Acceptance

Cradles accept tire widths from over 2.75 in. up to 4 in. and are designed for wheel sizes 22 in. or larger, covering most fat tire eBike configurations on the market.

What's Included

  • 2x Upper Wheel Cradle assemblies
  • 2x Lower Wheel Cradle assemblies
  • 4x 12 in. rubber straps with pull tabs and tension-fit hole locations
  • Hardware for installation on V-wing support arms
Complete Kit for One Fat eBike: The B02141 contains everything needed to cradle one fat tire electric bike on a compatible V-Lectric or Let's Go Aero V-Rack carrier. No additional cradle hardware is needed for a single bike setup.

Fitment -- V-Lectric eBike Carrier Models

This kit is the correct upfit accessory for the following V-Lectric eBike carrier part numbers:

  • B02615
  • B02639
  • B02158
  • B00390
  • B02301
  • B01175
Also Compatible with These Let's Go Aero Rack Lines (for Fat Bikes Only -- Does NOT Increase eBike Weight Limit): The B02141 cradle kit physically fits select Let's Go Aero models including the NEO, Nelson, Jack-It, Rack-It, and BikeWing-2 PRO (model B02189). When used on these non-eBike-rated racks, the kit accommodates fat tire widths but does not upgrade the rack's weight rating to support eBikes. Use only with bikes within the rack's published weight capacity when installed on non-V-Lectric models.

Bike Size and Weight Guidelines

Before loading, confirm your bike falls within the supported dimensions and weight. Fat eBikes vary widely in total weight, and the 60 lb per-bike limit applies to the cradle kit and must also be within your carrier's total rated capacity.

  • Tire width: over 2.75 in. up to 4 in.
  • Wheel size: 22 in. or larger
  • Maximum bike length: 72 in.
  • Maximum bike weight: 60 lbs per position
Maintenance Tip: After each trip, inspect the four rubber straps for cracking or permanent deformation, especially if the carrier is exposed to UV and heat. Let's Go Aero rubber straps are a consumable wear item -- replace if elasticity is compromised to maintain secure tire retention.

Kit Specifications

ManufacturerLet's Go Aero
Part NumberB02141
Kit Weight0.5 lbs.
Upper Cradle Assemblies2 (included)
Lower Cradle Assemblies2 (included)
Rubber Straps Included4x 12 in. rubber straps

Tire and Bike Compatibility

Minimum Tire WidthOver 2.75 in.
Maximum Tire Width4 in.
Minimum Wheel Diameter22 in.
Maximum Bike Length72 in.
Maximum Bike Weight60 lbs per bike position

V-Lectric Carrier Compatibility

B02615Compatible
B02639Compatible
B02158Compatible
B00390Compatible
B02301Compatible
B01175Compatible

Other Let's Go Aero Compatible Models

NEO SeriesFat bike fit only -- does not increase eBike weight limit
Nelson SeriesFat bike fit only -- does not increase eBike weight limit
Jack-It SeriesFat bike fit only -- does not increase eBike weight limit
Rack-It SeriesFat bike fit only -- does not increase eBike weight limit
BikeWing-2 PRO (B02189)Fat bike fit only -- does not increase eBike weight limit

Cradle Design

Release MechanismButton-trigger quick-release (no tools required)
Pin ConfigurationReversible for wheel size adjustment
Mount InterfaceV-wing support arms (Let's Go Aero V-Rack system)
Strap Length12 in.
Strap MaterialRubber with pull tab and tension-fit hole locations
Important Information
  • Maximum bike weight for this cradle kit is 60 lbs. Do not exceed this limit regardless of carrier capacity.
  • When installed on non-V-Lectric Let's Go Aero racks (NEO, Nelson, Jack-It, Rack-It, BikeWing-2 PRO), this kit does NOT increase the rack's weight rating to support electric bikes. eBikes may exceed those racks' published limits -- verify before loading.
  • This kit supports one (1) fat eBike. A second bike position requires an additional B02141 kit.
  • Confirm total carrier weight capacity against actual loaded bike weight before every trip -- eBike battery packs add significant weight.
  • Inspect rubber straps before each use. Cracked, torn, or permanently stretched straps must be replaced before transport.
  • Verify that your carrier is correctly installed on your hitch receiver and that the receiver rating matches or exceeds the combined weight of the carrier, bike, and any accessories.


Browse for more RV Accessories in the same category as this item:

Carriers & Haulers > Bike Carriers
Carriers & Haulers