Home > Lippert Repair Parts > Electric and Hydraulic Slide-Out Parts >

Lippert 134799 3-Room Hydraulic Slide-Out Standard MIRC Replacement Controller

Lippert 134799 Standard MIRC replacement controller module for 3-room hydraulic RV slide-out systems, front view showing connector ports.
Lippert 3 Slide-Out Room Standard MIRC
 
: $222.18
Part Number: 134799
Manufacturer: Lippert
NOTE: Ships in 5 to 7 days

Quantity in Stock :3

Free Shipping
Availability: In Stock
Qty:

 
Lippert 3-Room Hydraulic Slide-Out OEM Replacement Lippert 134799 Standard MIRC -- 3-Room Hydraulic Slide-Out Controller

When your hydraulic slide-outs stop responding or behave erratically, the Multi-Input Relay Center (MIRC) is a common failure point. The Lippert 134799 is an OEM-spec standard MIRC designed as a direct replacement for 3-room hydraulic slide-out systems, restoring proper slide operation without rewiring or fabricating custom solutions.

Restore Full Slide-Out Control with a Direct-Fit Replacement

The MIRC (Multi-Input Relay Center) is the electronic brain of Lippert's hydraulic slide-out systems. It receives input signals from wall switches and hand remotes, then coordinates the hydraulic pump and valve operations that extend and retract each slide room. Over time, relay contacts can burn, connectors corrode, or internal components fail -- especially in rigs that see heavy seasonal use or moisture exposure.

The Lippert 134799 Standard MIRC is built to OEM specification for systems managing 3 slide-out rooms. Swapping it in restores factory-level control logic, proper timing sequences, and slide room synchronization without modifying any existing wiring harnesses.

Direct OEM Replacement

Matches Lippert factory specs for 3-room hydraulic slide-out systems -- plug-in fit, no custom wiring required.

Standard MIRC Configuration

Designed for standard (non-leveling) 3-room hydraulic slide setups common across many RV brands using Lippert chassis components.

Lightweight Module

At only 2 lbs., the 134799 is easy to handle during installation and does not add meaningful weight to the chassis.

1-Year Limited Warranty

Backed by Lippert's limited 1-year manufacturer warranty for peace of mind on a critical electrical component.

What Is a MIRC and Why Does It Fail?

The Multi-Input Relay Center is mounted inside the RV, typically in a basement or chassis bay near the hydraulic pump. It contains relay banks, fuse protection, and logic circuitry that interpret switch commands and control which hydraulic valves open and in what sequence. Common failure symptoms include:

  • One or more slide rooms not responding to switch input
  • Slides moving in the wrong direction or failing to stop at full extension
  • Intermittent operation -- slides work sometimes but not reliably
  • Burned smell or visible relay damage on the module board
  • No operation after a power surge or battery disconnect event

Before replacing the MIRC, it is worth checking fuses, verifying 12V power at the module, and confirming switch continuity. However, if the module itself has failed, replacement is a straightforward swap that most RV owners with basic electrical skills can complete.

Direct-Fit Advantage: The 134799 uses the same connector footprint and wiring harness layout as the original Lippert standard MIRC for 3-room systems. In most cases, installation involves disconnecting the old module, mounting the new one in the same location, and reconnecting the existing harnesses -- no splicing needed.

Compatible Slide-Out System Background

Lippert hydraulic slide-out systems are found across a wide range of fifth wheels, travel trailers, and motorhomes produced by manufacturers including Forest River, Jayco, Coachmen, Heartland, and many others. The "standard" MIRC designation distinguishes this unit from leveling-integrated MIRC variants -- confirm your existing module's part number before ordering to ensure you are replacing like-for-like.

Confirm Your Existing Part Number: Lippert produces several MIRC variants (2-room, 3-room, leveling-integrated, and combo units). The 134799 is specifically the standard 3-room version. Locate your existing MIRC module and verify the part number printed on the label before ordering.

Installation Tips

  • Disconnect shore power and disconnect the 12V house battery before removing the old MIRC.
  • Photograph all existing harness connections before unplugging -- this makes reconnection straightforward.
  • Inspect all connectors for corrosion or pin damage and clean as needed before installing the new module.
  • After installation, cycle each slide room individually to confirm correct direction and stop behavior before road travel.
Maintenance Note: Moisture intrusion into the MIRC bay is a leading cause of premature failure. After installation, check that any existing weatherstrip or bay door seals are intact, and consider applying dielectric grease to harness connectors to slow future corrosion.

Product Specifications

ManufacturerLippert Components
Part Number134799
Product TypeStandard MIRC (Multi-Input Relay Center)
Slide Room Capacity3 rooms
System TypeHydraulic slide-out (standard, non-leveling)
Weight2 lbs.

Warranty Information

Warranty CoverageLimited 1-year manufacturer warranty
Warranty ProviderLippert Components

Compatibility Notes

Fits System Type3-room hydraulic slide-out systems using Lippert standard MIRC
ReplacesOriginal Lippert standard MIRC on 3-room hydraulic configurations
Not Compatible With2-room MIRC systems, leveling-integrated MIRC variants, or electric slide-out systems
Common RV Brands Using Lippert Slide SystemsForest River, Jayco, Heartland, Coachmen, Keystone, and others

In the Box

Included1x Lippert 134799 Standard MIRC module
Not IncludedMounting hardware, wiring harnesses, installation instructions (reuse existing)
Important Information
  • Verify your existing MIRC part number is 134799 before ordering -- Lippert makes multiple MIRC variants and they are not interchangeable.
  • This is a standard 3-room MIRC only. It is not compatible with 2-room systems, leveling-integrated systems, or electric slide-out systems.
  • Always disconnect shore power and the 12V battery before removing or installing this module.
  • This is an electronic control module -- it is not returnable once installed. Confirm fitment by matching the part number on your existing unit before installation.
  • If slide-out issues persist after replacement, inspect hydraulic pump, valve solenoids, and switch wiring before assuming further module failure.


Browse for more RV Accessories in the same category as this item:

Lippert Repair Parts > Electric and Hydraulic Slide-Out Parts
Lippert Repair Parts