Genuine MORryde rubber shear spring for RL Suspension Systems. Density #75 — for GAWR 8,500–10,500 lbs. 2 blocks bonded together. No bolts required.
The MORryde DSR108-075 is a genuine OEM-grade replacement rubber shear spring engineered for use in MORryde's Rubber Leaf (RL) Suspension Systems. Designed to work in concert with your existing leaf spring suspension, this double-series rubber block absorbs road shock and vibration to deliver a softer, smoother, more comfortable ride — protecting both passengers and the vehicle chassis from the stress of rough roads.
The DSR108-075 features two rubber blocks pre-bonded together on a single mounting plate, eliminating the need for separate hardware or bolts. The #75 density designation indicates this spring is matched to vehicles with a Gross Axle Weight Rating (GAWR) of 8,500 to 10,500 lbs. Verify the number stamped on your original spring before ordering to ensure the correct rubber density for your application.
Two rubber blocks are permanently bonded together on one plate — no separate bolts or assembly hardware required
Absorbs road shock and reduces vibration transmitted to the chassis, frame, and passengers
DSR springs are compatible with any MORryde RL suspension system — not just the model originally installed
#75 density rubber is engineered specifically for GAWR ranges of 8,500 to 10,500 lbs for proper load support
Rubber shear springs come in multiple density ratings. Check the number stamped directly on your original spring before placing your order. The stamped number corresponds to the part number suffix: Example: A spring stamped "75" = DSR108-075 (this part) Using the wrong density can result in improper load support, premature wear, or degraded ride quality. Your vehicle's Gross Axle Weight Rating (GAWR) determines which density is correct. If the original spring is missing or unreadable, consult your vehicle documentation or contact MORryde directly at (574) 293-1581.
The DSR108-075 is a direct, updated replacement for the following older MO-series shear springs: • #2 MO Shear Spring • #6 MO Shear Spring • #7 MO Shear Spring DSR-series springs can be used as a drop-in replacement on any MORryde RL suspension system regardless of original spring designation, as long as the rubber density number matches your GAWR requirements.
Replacing Your Rubber Shear Spring: 1. Verify Density: Check the number stamped on the original spring to confirm the DSR108-075 is the correct replacement 2. Safely Support the Vehicle: Use jack stands to safely support the axle and relieve tension from the suspension 3. Remove the Old Spring: Unbolt the mounting plate hardware securing the worn shear spring to the carrier bracket 4. Install DSR108-075: Position the new bonded spring block onto the carrier bracket, aligning the plate holes (3" x 9" spacing) 5. Secure the Plate: Torque mounting hardware to MORryde specifications per your system's documentation 6. Lower Vehicle and Test: Check ride height and suspension travel before returning to service Professional installation is recommended. Consult MORryde's product documentation for torque specs and system-specific guidance.
In The Box: • (1) DSR108-075 Rubber Shear Spring Assembly • 2 Rubber Blocks Pre-Bonded to Mounting Plate NOT Included: • Mounting bolts/hardware (reuse existing or source separately) • Carrier bracket or other RL system components • Installation tools
MORryde Technical Support: Phone: (574) 293-1581 Email: [email protected] Made in Elkhart, Indiana, USA MORryde is an ISO 9001 certified manufacturer of suspension, hitch, and specialty RV products.
All DSR108 springs share the same plate size (5" x 10") and bonded double-block design. The only difference is rubber density — matched to your vehicle's GAWR. Always verify the number stamped on your original spring.
Important: GAWR ranges shown are general guidelines. Always confirm by reading the number stamped on your existing spring. Contact MORryde at (574) 293-1581 if you are unsure which density is correct for your vehicle.