Home > Sanitation > Holding Tank Ventilation >

Camco 40597 Cyclone RV Sewer Vent Cap Black -- Rotating 360-Degree Wind-Powered Odor Exhaust for 1-1/2 in. PVC Vent Pipe

Camco 40597 Cyclone RV Sewer Vent Cap in black, rotating 360-degree wind-powered design for 1-1/2 inch PVC holding tank vent pipes
Camco Cyclone RV Sewer Vent Cap - Black
 
Alternative Views:


List Price: $35.09
: $26.99
You save $8.10!
Part Number: 40597
Manufacturer: Camco

Quantity in Stock :34

Availability: In Stock
Qty:

 
CamcoPart 40597UV-Resistant ResinCamco 40597 Cyclone RV Sewer Vent Cap -- Black

Stop holding tank odors before they become a campsite problem. The Camco Cyclone uses wind energy -- even a light breeze -- to spin 360 degrees and generate a continuous vortex that actively pulls sewer gases up through your roof vent and away from your living space. No electricity, no chemicals, just physics.

Wind-Powered Odor Exhaust That Works Around the Clock

Most stock sewer vent caps are passive -- they block rain and bugs but do nothing to move air. The Cyclone is different. Its dynamically engineered housing catches wind from any direction and converts it into a spinning vortex inside the cap, creating a low-pressure zone that draws air and odor up and out of your holding tank system continuously.

The cap rotates a full 360 degrees on its base, so it self-orients to the prevailing wind whether you are parked nose-in, backed up to a hookup, or out boondocking with no hookups at all. There is no preferred orientation -- just mount it level and let it work.

360-Degree Auto-Rotation

Automatically aligns to wind direction so vortex suction is maintained regardless of how your rig is parked.

Wind-Powered Vortex Action

Dynamically shaped housing converts even gentle breezes into sustained upward airflow through the holding tank vent stack.

UV-Resistant Rustproof Resin

Engineered resin resists sun-induced brittleness and won't rust or corrode -- built for full-time roof exposure.

Low-Profile Design

At 9-1/4 in. tall and under 6-1/2 in. wide, the Cyclone clears most slide toppers and awning arms without clearance issues.

Fitment -- What Pipes This Cap Fits

The Camco 40597 Cyclone is engineered to fit most 1-1/2 inch PVC holding tank vent pipes -- the standard diameter used on the vast majority of Class A, Class C, fifth-wheel, and travel trailer builds. If you are unsure of your pipe diameter, measure the outside diameter of the existing pipe stub coming through the roof; 1-1/2 in. Schedule 40 PVC has a nominal OD of approximately 1.9 in.

Standard Fit: This cap replaces most OEM sewer vent covers on travel trailers, fifth wheels, Class A and Class C motorhomes, and toy haulers that use 1-1/2 in. PVC vent stacks. It is not designed for 3 in. or 4 in. roof vents.

Installation Overview

Installation is a straightforward DIY job. The cap mounts directly over the existing PVC vent pipe stub on a level roof surface. A proper seal with 100% silicone caulk prevents water intrusion at the base.

  • Remove the old vent cap -- a utility knife and putty knife handle most OEM caps.
  • Clean the pipe stub and roof surface thoroughly before applying caulk.
  • Apply a bead of 100% silicone caulk around the pipe stub base.
  • Position the Cyclone cap over the pipe, press down firmly to seat the caulk bead.
  • Secure with screws using a 3/32 in. drill bit for pilot holes and a Phillips-head screwdriver.
  • Allow caulk to cure fully before exposing to rain -- typically 24 hours.
Level Surface Required: The cap must be installed on a level or near-level roof section. Installing on a significant slope can impair the rotation bearing and reduce vortex efficiency. If your vent pipe exits on a sloped section, use a leveling base or extension flange before installing.
Tools Needed (not included): Utility knife, putty knife, 100% silicone caulk (not included), drill with 3/32 in. bit, and a Phillips-head screwdriver. The cap and mounting screws are included.

Why Upgrade from a Standard Vent Cap

OEM vent caps on most production RVs are basic mushroom or flat covers -- they keep rain out but provide zero active ventilation. In hot weather, holding tank gases build up pressure and can backdraft into the coach through toilet seals and drain traps, causing odor inside the rig. The Cyclone eliminates this by maintaining a consistent negative pressure at the top of the vent stack.

Maintenance Tip: Inspect the rotation bearing annually and clear any debris -- leaves, pine needles, road grime -- that may have accumulated inside the cap housing. A stuck rotor won't vortex. A quick rinse with a hose and a spin-check takes under two minutes.
Pair It With: For maximum odor control, combine the Cyclone cap with a holding tank treatment like Camco TST or Thetford AquaKem. The Cyclone handles roof-side ventilation; tank treatment handles biological odor at the source.

Physical Specifications

Overall Dimensions6-1/2 in. L x 6-1/4 in. W x 9-1/4 in. H
Weight0.65 lbs.
ColorBlack
ProfileLow-profile rotating cap

Fitment and Compatibility

Pipe Size1-1/2 in. PVC holding tank vent pipe (nominal)
Pipe TypeStandard Schedule 40 PVC
Compatible ApplicationsTravel trailers, fifth wheels, Class A, Class B+, Class C motorhomes, toy haulers
Installation SurfaceLevel roof surface recommended

Materials and Construction

Housing MaterialUV-resistant, rustproof engineered resin
Rotation360 degrees, wind-driven, self-orienting
FastenersScrew-mounted (screws included); pilot hole 3/32 in.
Sealant Required100% silicone caulk (not included)

Part and Warranty Information

ManufacturerCamco
Camco Part Number40597
SKU22-0003
UPC014717405973
WarrantyLimited 90-Day Manufacturer Warranty
Important Information
  • Designed for 1-1/2 in. PVC holding tank vent pipes only -- not compatible with 3 in. or 4 in. drain/vent stacks.
  • Installation on a level surface is required; significant roof slope will reduce rotation efficiency and vortex performance.
  • 100% silicone caulk is required for a watertight installation and is NOT included -- purchase separately before starting.
  • Allow silicone caulk to cure fully (typically 24 hours) before the rig is exposed to rain or washing.
  • This cap replaces only the roof vent cover -- it does not address odors caused by dried-out P-traps, failed toilet seals, or improperly vented holding tanks.
  • Inspect the rotation bearing annually; debris accumulation can prevent the cap from spinning and will eliminate vortex function.
  • Limited 90-Day Manufacturer Warranty covers defects in materials and workmanship under normal use.


Browse for more RV Accessories in the same category as this item:

Sanitation > Holding Tank Ventilation
Sanitation


$15.49
$49.30
$141.49
$89.90