Replaces factory steel equalizers with shock-absorbing rubber compression springs. 4" of suspension travel. Bolt-on installation — no crossmember required. Engineered for trailers up to 8,000 lbs GAWR. The most rigorously-tested MORryde equalizer suspension to date.
Rough roads are the enemy of your fifth wheel or travel trailer. Every pothole, expansion joint, and rutted surface sends shock and vibration directly through your trailer's frame, stressing the structure, rattling contents, and accelerating wear on every component. The factory steel equalizers that came with most trailers do almost nothing to absorb that energy — they simply transfer it.
The MORryde AllTrek 4000™ (TG2-33) replaces those steel equalizers with shock-absorbing rubber compression springs that allow up to 4" of suspension travel — cushioning the impact before it reaches your trailer. With over 40% more rubber than prior MORryde equalizer designs, the AllTrek 4000™ is the most rigorously-tested equalizer suspension MORryde has ever produced, engineered for tandem axle trailers with a 33" axle wheelbase spacing and rated for axles up to 8,000 lbs GAWR. Installation is bolt-on with no crossmember required, and each kit includes the 2 equalizers needed for one complete tandem axle RV.
Rubber compression springs allow up to 4" of total suspension travel — absorbing road shock before it reaches the trailer frame
No crossmember required — replaces factory steel equalizers at existing mounting points for straightforward installation
Over 40% more rubber than previous MORryde equalizer designs — greater cushioning, smoother towing, and better road shock protection
MORryde's most extensively tested equalizer suspension to date — engineered and validated for long-term durability and performance
Two critical measurements must be confirmed before purchasing: 1. Wheelbase Spacing — 33" vs. 35": The TG2-33 is specifically for trailers with 33" center-to-center axle spacing. If your tandem axles are spaced 35" apart, you need the TG2-35 instead. Measure the distance between the center of your front axle and the center of your rear axle to confirm. 2. Tandem Axle Only (Currently): The AllTrek 4000™ is currently available for tandem axle trailers only. It is not available for triple axle applications at this time. 3. GAWR: The AllTrek 4000™ is engineered for axles rated up to 8,000 lbs GAWR. Confirm your axle ratings fall within this range. Use MORryde's AllTrek 4000™ Qualifier guide to confirm your specific trailer is compatible before purchasing.
What's in a Tandem Kit: Each TG2-33 tandem kit includes 2 equalizers — everything needed for one complete tandem axle RV. This is the correct purchase for a single tandem axle fifth wheel or travel trailer. Currently Tandem Only: The AllTrek 4000™ is currently available for tandem axle applications only. Triple axle configurations are not currently supported. Wheelbase Options: • TG2-33 (This Product) — 33" center-to-center axle spacing • TG2-35 — 35" center-to-center axle spacing Measure your axle spacing carefully — using the wrong wheelbase kit will result in improper fit and installation.
Installation Steps (Professional Installation Recommended): 1. Verify Compatibility: Confirm 33" wheelbase spacing, tandem axle configuration, and GAWR within 8,000 lbs using MORryde's Qualifier guide 2. Safely Support the Trailer: Use proper jack stands to safely support the trailer frame and relieve load from the suspension 3. Remove Factory Steel Equalizers: Unbolt and remove the existing steel equalizers from their mounting locations on both axle beams 4. Install AllTrek 4000™ Equalizers: Position the rubber equalizer assemblies at the same mounting locations and bolt into place 5. Torque to Specification: Tighten all hardware to MORryde's specified torque values per the installation instructions 6. Lower and Inspect: Lower the trailer, verify equalizer seating, and check suspension function before returning to service Professional installation recommended. Refer to MORryde's AllTrek 4000™ Tandem Installation Instructions for complete torque specifications and step-by-step guidance.
In The Box (Tandem Kit): • (2) AllTrek 4000™ Rubber Equalizer Assemblies • Mounting Hardware • Glide Pads • Bronze Bushings • Installation Instructions NOT Required: • No crossmember needed for installation 35" Wheelbase Version: • TG2-35 — same system for 35" axle spacing
MORryde Technical Support: Phone: (574) 293-1581 Email: [email protected] Made in Elkhart, Indiana, USA MORryde is an ISO 9001 certified manufacturer of suspension and specialty vehicle products.
Both kits are identical in design and performance. The only difference is axle wheelbase spacing. Measure the center-to-center distance between your tandem axles before ordering.
Measure the center-to-center distance between your tandem axles to confirm which kit is correct. Contact MORryde at (574) 293-1581 if you are unsure of your wheelbase spacing.