1/2" H x 7/16" W EPDM sponge rubber hollow half-round weatherstrip with recessed skirted 3M Peel-N-Stick adhesive. Prevents moisture and debris from collecting behind the seal. Ideal for RV compartment doors and hatches. Keeps out moisture, bugs, wind, and debris. Black, 15 ft pre-cut strip. Hand crafted in the USA.
The Steele Rubber Products 83-0130-277 is a 1/2" H x 7/16" W Peel-N-Stick Hollow Half-Round sponge rubber RV seal — a straightforward, dependable weatherstrip built for compartment doors and hatches across a wide range of RV makes and models. The hollow half-round profile sits squarely between the small and large half-round sizes, making it a versatile fit for the mid-size compartment door openings and hatches that are common across travel trailers, fifth wheels, and Class A and C motorhomes.
The hollow interior of the profile is what makes it effective as a sealing extrusion. Unlike a solid half-round that can resist compression, the hollow dome deflects readily under door closure force and distributes that compression evenly across its full width — forming a consistent, gap-free contact seal along the entire door perimeter. When the door is opened, the profile springs back to its original shape cleanly, ready to seal again on the next closure.
The recessed skirted 3M Peel-N-Stick adhesive is a significant upgrade over standard exposed adhesive strips. The skirting extends the rubber base outward around the adhesive edges, shielding them from direct moisture contact, road debris, and UV degradation — the most common causes of adhesive edge failure in exposed weatherstrips. This design produces a clean, finished look with no visible adhesive after installation and protects the bond for lasting adhesion through years of outdoor use.
Hollow dome deflects evenly under door closure and springs back cleanly — consistent perimeter seal for compartment doors and hatches across repeated open/close cycles
Skirting shields adhesive edges from moisture, debris, and UV — prevents the edge-lifting and adhesive failure common with exposed backing strips; clean finished look after installation
Full perimeter compression seal closes gaps in old or worn door seals — keeps moisture, insects, wind, and road debris out of the coach interior
Will not fade, shrink, or crack — excellent resistance to moisture, ozone, and UV exposure for long-term outdoor performance through all seasons
Apply between 60°F and 104°F (15°C–40°C) for best adhesive bond strength. The temperature difference between the seal and the bonding surface should be as small as possible — avoid applying in direct sunlight on a very hot surface or in cold ambient conditions. Surface Preparation: Completely remove all old seal material, adhesive residue, dirt, wax, and moisture before applying. Wipe the bonding surface with isopropyl alcohol and allow to fully dry. The surface must be completely clean and dry before applying — any contamination or moisture will significantly reduce adhesion strength.
Primary Part Number: 83-0130-277 Ideal For: A broad range of RV compartment doors, access doors, and hatches — the 1/2" H x 7/16" W hollow half-round profile is compatible with mid-size door openings across travel trailers, fifth wheels, and motorhomes. Always measure your existing seal profile before ordering to confirm the dimensions are a match. Available Lengths (Same Profile): • 5 ft — same profile, shortest pre-cut length • 10 ft — same profile • 15 ft — Part 83-0130-277 (This Item) • 30 ft — same profile, longest pre-cut length • Also available by the foot for custom lengths Note: Always confirm the profile dimensions (1/2" H x 7/16" W) match your existing seal before purchasing. Application temperature 60°F–104°F.
What You Need: No tools required. Recommended supplies: isopropyl alcohol, clean cloth, tape measure, scissors or utility knife. Basic Installation Steps: 1. Check Temperature: Confirm ambient and surface temp is between 60°F and 104°F (15°C–40°C) — minimize temperature difference between seal and bonding surface 2. Remove Old Seal: Completely remove all old weatherstrip material and adhesive residue from the mounting surface 3. Clean & Dry: Wipe the bonding surface with isopropyl alcohol and allow to fully dry — do not apply to a damp or contaminated surface 4. Measure & Cut: Measure the door or hatch perimeter and cut the seal to length with scissors or a utility knife 5. Peel & Press: Starting at one corner, remove backing a few inches at a time and press the skirted base firmly onto the mounting surface — do not remove all backing at once 6. Test the Closure: Close the compartment door or hatch to confirm the hollow dome compresses evenly and creates a consistent, gap-free seal around the full perimeter
Included: • One (1) 83-0130-277 Peel-N-Stick Hollow Half-Round RV Seal • 15-foot pre-cut strip • EPDM sponge rubber, 1/2" H x 7/16" W hollow half-round profile • 3M Peel-N-Stick adhesive with recessed skirted design NOT Included: • Isopropyl alcohol or adhesive remover for surface prep • Clean cloth, tape measure, scissors or utility knife
All lengths share the same 1/2" H x 7/16" W EPDM sponge hollow half-round profile with recessed skirted 3M Peel-N-Stick adhesive. Also available by the foot for custom lengths. When ordering by the foot, the seal ships as one continuous piece. Order the length that best matches your project to minimize waste.