3/4" H x 3/4" W 100% EPDM sponge rubber large hollow half-round seal with recessed skirted 3M Peel-N-Stick adhesive. Robust design for high-use compartment doors and hatches. Protects against moisture, bugs, wind, and debris. Commonly found on Forest River and Keystone models. Black, 15 ft pre-cut strip.
The Steele Rubber Products 83-1025-283 is a 3/4" H x 3/4" W Peel-N-Stick Large Hollow Half-Round sponge rubber RV seal ā a top-quality 100% EPDM extrusion designed for compartment doors and hatches. The large hollow half-round profile is one of the more versatile and widely used RV door seal shapes: the rounded dome compresses fully under door closure force and springs back cleanly, creating a consistent perimeter seal across the full length of the door or hatch frame. The larger 3/4" height and width make it an ideal fit for applications where smaller half-round profiles would leave gaps under a door with a heavier or less precise closure.
The recessed adhesive design is a key feature of this seal. The skirted 3M Peel-N-Stick backing is set into the base of the extrusion rather than sitting exposed on the outer edges. This recessed layout shields the adhesive from direct moisture exposure, road debris, and UV degradation ā keeping the bond strong through seasons of use and preventing the edge-lifting and adhesive failure that commonly occurs with non-skirted adhesive-backed seals.
This robust construction makes the 83-1025-283 well suited for high-use compartment doors and hatches that are opened and closed frequently. It is commonly found on Forest River and Keystone models and provides lasting protection against moisture, bugs, wind, and debris getting inside the coach through gaps around worn or damaged door seals. The 15-foot pre-cut strip covers a full compartment door perimeter or multiple shorter replacement runs.
3/4" H x 3/4" dome profile compresses fully under door closure and springs back cleanly ā consistent perimeter seal for larger compartment doors and hatches
Skirted 3M adhesive is recessed into the base ā shields the bond from moisture, debris, and UV exposure for long-lasting adhesion and no exposed adhesive edges
Engineered for high-use compartment doors and hatches ā durable EPDM sponge construction holds up through repeated daily open/close cycles
Superior grade EPDM ā will not fade, shrink, or crack; excellent resistance to moisture, ozone, and UV for long-term outdoor performance
Apply between 60Ā°F and 104Ā°F (15Ā°Cā40Ā°C) for best adhesive bond strength. The temperature difference between the seal and the bonding surface should be as small as possible ā avoid applying in direct sunlight on a very hot surface or in cold ambient conditions. Surface Preparation: Completely remove all old seal material, adhesive residue, dirt, wax, and moisture before applying. Wipe the bonding surface with isopropyl alcohol and allow to fully dry. Thorough surface prep is the single most important factor in long-term bond performance ā do not apply to a damp or contaminated surface.
Primary Part Number: 83-1025-283 Known RV Fitment (not exhaustive): ā¢ Forest River models ā compartment doors and hatches ā¢ Keystone models ā compartment doors and hatches Available Lengths (Same Profile): ā¢ 5 ft ā same profile, shortest pre-cut length ā¢ 10 ft ā same profile ā¢ 15 ft ā Part 83-1025-283 (This Item) ā¢ 30 ft ā same profile, longest pre-cut length ā¢ Also available by the foot for custom lengths Note: Compatibility is not guaranteed. Always confirm fit against your specific model before purchasing. Application temperature 60Ā°Fā104Ā°F.
What You Need: No tools required for adhesive application. Recommended supplies: isopropyl alcohol, clean cloth, tape measure, scissors or utility knife. Basic Installation Steps: 1. Check Temperature: Confirm ambient and surface temp is between 60Ā°F and 104Ā°F (15Ā°Cā40Ā°C) ā minimize temperature difference between seal and bonding surface 2. Remove Old Seal: Completely remove all old weatherstrip material and adhesive residue from the mounting surface 3. Clean & Dry: Wipe the bonding surface with isopropyl alcohol and allow to fully dry before applying 4. Measure & Cut: Measure the door or hatch perimeter and cut the seal to length with scissors or a utility knife 5. Peel & Press: Starting at one corner, remove the backing a few inches at a time and press the skirted base firmly onto the mounting surface ā do not remove all backing at once 6. Test the Closure: Close the compartment door or hatch to confirm the hollow dome compresses evenly and creates a consistent, gap-free seal around the full perimeter
Included: ā¢ One (1) 83-1025-283 Peel-N-Stick Hollow Half-Round RV Seal ā¢ 15-foot pre-cut strip ā¢ 100% EPDM sponge rubber, 3/4" H x 3/4" W large hollow half-round profile ā¢ 3M Peel-N-Stick adhesive with recessed skirted design NOT Included: ā¢ Isopropyl alcohol or adhesive remover for surface prep ā¢ Clean cloth, tape measure, scissors or utility knife
All lengths share the same 3/4" H x 3/4" W 100% EPDM sponge large hollow half-round profile with recessed skirted 3M Peel-N-Stick adhesive. Also available by the foot for custom lengths. Order the length that best matches your project to minimize waste.