Home > RV Accessories > Carpet Protection >

Lippert Slide-Out Slicker Set LIP134993 -- 40 Inch Floor Protectors, 2-Pack, White
Lippert LIP134993 Slide-Out Slicker Set, 40-inch white floor protectors for RV slide room carpet and tile protection, 2-pack
AP Products 013-410051 Lippert Slide-Out Slicker Set
  
Alternative Views:
List Price: $82.99
: $82.99
Part Number: 134993
Manufacturer: Lippert

Quantity in Stock :25

Availability: In Stock
Qty:

 
Lippert 2-Pack No Tools Required Lippert Slide-Out Slicker Set -- LIP134993

The first thing to show wear in any RV with a slide room is the carpet along the threshold. Lippert's Slide-Out Slicker Set gives you a dead-simple fix: lay the slickers down before retracting, and they act as a barrier between the slide room floor edge and your carpet or tile. No adhesive, no brackets, no tools -- just lift, place, and retract.

Stop Slide Room Wear Before It Starts

Every time a slide room retracts, its floor edge drags across the interior floor surface. Over months and seasons, this grinds debris into carpet fibers and scratches tile finishes. The Lippert Slide-Out Slicker acts as a low-profile ramp and shield, letting the slide room glide over the protected surface rather than chewing into it.

At nearly 40 inches long and 5 inches wide, each slicker spans the full depth of a standard slide room threshold. The slim 0.5-inch profile keeps the slicker flat and stable without creating a trip hazard. When the room is fully extended and you don't need them, they store flat under a bunk, in a basement bay, or in any flat storage space.

Instant Installation

Lift the carpet flap at the slide room threshold, lay the slicker flat against the end wall, and retract. No cutting, drilling, or adhesive required.

Carpet and Tile Safe

Smooth low-friction surface protects carpet fibers from compression and abrasion and prevents tile scratching during slide-out operation.

Two-Pack Included

Covers both sides of a single slide room or one side of two separate slide rooms. Sold as a matched pair at 40 inches each.

Flat and Compact Storage

Once the slide room is extended, slickers lay flat and store easily -- under a mattress, in a cabinet, or in a storage bay -- until you need them again.

How to Use Slide-Out Slickers

Proper placement takes less than a minute and makes a measurable difference in floor longevity:

  • Before retracting your slide room, position one slicker on each side of the opening with the slicker butted against the threshold end wall.
  • If your RV has a carpet flap at the slide room edge, tuck the slicker under it so it lies flush.
  • Retract the slide room normally -- the slicker rides between the slide floor edge and your interior floor surface.
  • Once the room is fully retracted, the slickers are held in place. When extending the room again, retrieve and store them.
Genuine Lippert Component: Part number LIP134993 is a factory Lippert accessory designed to work with standard residential-style slide room systems found on a wide range of travel trailers, fifth wheels, and motorhomes. It is not a generic aftermarket item.

What Wears Out Without Protection

Without a slicker in place, the bottom edge of the slide room floor -- often a hard composite or laminated panel -- contacts the carpet or tile directly. Common damage over a single season of weekend use includes:

  • Flattened or shredded carpet pile along the slide room perimeter
  • Dirt and grit dragged onto the interior floor by the retracting edge
  • Tile surface scratches from hard panel edges
  • Adhesive failure on peel-and-stick flooring at the threshold

Replacing RV flooring -- especially if it extends under the slide room -- is a significant repair. Slide-Out Slickers are a low-cost preventive measure by comparison.

Storage Tip: Store both slickers together in a flat zippered bag or bungee-strapped to the inside of a basement compartment wall. Keeping them accessible means you will actually use them every time you move camp.
Maintenance Note: Wipe slickers clean after each use to prevent grit buildup on the slicker surface itself. Even a low-friction surface will cause wear if it has sand or debris on it.

Product Specifications

ManufacturerLippert Components
Part NumberLIP134993
UPC848150011718
SKU14-8151

Physical Dimensions

Length40 inches (per slicker)
Width5 inches
Thickness0.5 inches
ColorWhite
Quantity in Pack2 slickers

What's in the Box

Included2 x Slide-Out Floor Protectors (Slickers)
Tools RequiredNone
Hardware RequiredNone
Adhesive RequiredNo

Compatibility

ApplicationRV slide rooms with carpeted or tiled interior floors
RV TypesTravel trailers, fifth wheels, motorhomes
Floor TypesCarpet, tile, vinyl, laminate
Slide Room Width CoverageOne slicker per side of slide opening; 40 in. covers most standard thresholds
Important Information
  • Slickers must be removed or repositioned before extending the slide room -- leaving them pinned under a fully retracted slide room and then extending without retrieving them can damage the slicker or the slide room seal.
  • Not designed for use as a permanent floor covering. Remove and store once the slide room is fully extended.
  • Do not use on heavily soiled or wet floors -- debris on the slicker surface can still cause abrasion.
  • This set covers one slide room (both sides) or one side of two slide rooms. For two full slide rooms, two sets are recommended.
  • Verify your slide room threshold length before ordering. The 40-inch slicker length fits most standard residential-style slide rooms but may not span extra-wide full-wall slide openings.


Browse for more RV Accessories in the same category as this item:

RV Accessories > Carpet Protection
Lippert Repair Parts > Electric and Hydraulic Slide-Out Parts
RV Accessories
Lippert Repair Parts