EPDM rubber "P" profile wiper and bulb combination seal with Peel-N-Stick adhesive skirting. 3/4" H x 2-1/2" W — 30 ft roll. Black. Commonly found on early 2000s Bounder Class A motorhomes and Cedar Creek RLTS fifth wheels.
The Steele Rubber Products 90-3619-265 is a 2-1/2" Peel-N-Stick "P" Profile Wiper Seal that combines a wiper blade and a hollow bulb in a single EPDM rubber extrusion. The distinctive "P" shape — a wiper blade extending from a rounded hollow bulb — creates a dynamic seal that wipes the slide-out surface clean during retraction and compresses firmly against the RV body when the slide-out is fully closed, blocking water, dust, and insects from entering the coach.
Made from 100% EPDM rubber with superior wear and weather resistance, this seal features a reinforced wiper section for long-term durability through repeated slide-out cycling. The Peel-N-Stick backing is surrounded by protective skirting that covers the adhesive tape edges for a clean finished look and improved long-term bond protection. Ideal for more confined slide-out box designs where a combined wiper-and-bulb profile handles both sealing functions in one strip.
Commonly found on early 2000s Bounder Class A motorhomes and Cedar Creek RLTS fifth wheels, and serves as an exact replacement for many current Class A RV designs. The 30-foot roll provides generous coverage for a full slide-out perimeter or two-side replacement. Also known as base part 70-4174-265.
Combined wiper blade and hollow bulb in one strip — wipes clean on retraction, seals firmly when closed
Reinforced wiper blade construction ensures long-term durability through thousands of slide-out cycles
Protective skirting surrounds the adhesive tape for a finished look and shields the bond edges from debris
100% EPDM rubber — superior weather, UV, and ozone resistance. Will not fade, shrink, or crack
This seal is known to fit early 2000s Bounder Class A motorhomes and Cedar Creek RLTS fifth wheels, and serves as an exact replacement for many current Class A RV designs. Compatibility is not guaranteed for all years and configurations — this is not an exhaustive fitment list. The "P" profile combines a wiper blade and bulb in a single strip. Before ordering, confirm your existing seal uses a "P" shaped profile (not a flat blade wiper, push-on wiper, or separate bulb-and-wiper system) and that dimensions match: 3/4" H x 2-1/2" W. Always clean the mounting surface thoroughly before applying the Peel-N-Stick adhesive.
Primary Part Number: 90-3619-265 Base Part Number: 70-4174-265 Available Lengths (Same Profile): • 15 ft — Part 90-3618-265 • 30 ft — Part 90-3619-265 (This Item) • 60 ft — Part 90-3620-265 Note: Also available by the foot for custom lengths — select the number of feet needed and it will be sent as one continuous piece.
What You Need: No hardware or tools required. Surface prep supplies recommended: isopropyl alcohol or adhesive remover, clean cloth, and tape measure. Basic Installation Steps: 1. Prep the Surface: Completely remove all old seals, adhesive residue, dirt, wax, and moisture from the mounting surface 2. Clean & Dry: Wipe with isopropyl alcohol and allow to fully dry before applying 3. Measure & Cut: Cut the seal to the required length with scissors or a sharp utility knife 4. Orient Correctly: The "P" bulb should face the RV body; the wiper blade should face outward to sweep the slide-out surface during retraction 5. Peel & Press: Remove the adhesive backing and press the seal firmly onto the mounting surface, working from one end to the other 6. Test the Slide: Extend and retract the slide-out to confirm the wiper sweeps cleanly and the bulb seals firmly when closed
Included: • One (1) 90-3619-265 Peel-N-Stick "P" Profile Wiper Seal • 30-foot pre-cut roll • Peel-N-Stick adhesive with protective skirting • 100% EPDM black rubber construction NOT Included — Recommended for Installation: • Isopropyl alcohol or adhesive remover for surface prep • Clean cloth or paper towels • Scissors or utility knife, tape measure
All three lengths share the same "P" profile, EPDM rubber construction, and Peel-N-Stick installation. Order the length that best matches your project to minimize waste. Also available by the foot for custom lengths.