Garnet 709-RVC-PM SeeLevel II 3 Tank Monitoring System with Alarm

Garnet 709-RVC-PM SeeLevel II Tank Monitoring System with Alarm

Alternative Views:

Monitors battery voltage, fresh, grey and black water levels, includes an RV-C network interface and a common alarm output which is programmable for level and polarity and also includes a momentary pump switch.

List Price: $394.11

: $375.45

You save $18.66!

Part Number: 709-RVC-PM-1003
Manufacturer: Garnet Instruments

Quantity in Stock :3

Availability: In Stock

Select Tank Sensor Sizes

Fresh Water Tank*:

Grey Water Tank*:

Black Water Tank*:

Qty:

The Garnet 709-RVC-PM SeeLevel II Tank Monitoring System with Alarm is designed for accurate level measurement of motorhomes and trailers with three holding tanks. This system monitors battery voltage, fresh, grey and black water levels. The level in percent is shown on a three digit LED display. This model includes an RV-C network interface and a common alarm output which is programmable for level and polarity and also includes a momentary pump switch.

709-RVC-PM System Monitors
- battery voltage
- fresh water tank
- grey water tank
- black water tank
Provides accurate tank level information using percentage of full readout
Tanks are monitored using Garnet’s proprietary external level sensing technology
- This ends fouling problems caused by debris build-up in the holding tank
- Detailed diagnostic information monitors sender operation
Three different sender sizes available to fit your tanks
- 710-AR2 Sender: Dimensions: 9" high x 2.2" wide
  - Resolution: .25" Segments
  - Measurable range: 3" to 9"
  - Tank heights from 3.5" to 10.5" (single sensor)
  - Up to 19.5" (dual stacked sensors).
- 710-ES3 Sender:
  - Dimensions 12.15” high x 2.2” wide
  - Resolution: .33" Segments
  - Measurable range: 4" to 12"
  - Tank heights from 4.5" to 14" (single sensor)
  - Up to 26” (dual stacked sensors)
- 710-SS2 Sender: Dimensions 16" high x 2" wide
  - Resolution: .44" Segments
  - Measurable range: 6" to 16"
  - Tank heights from 7" to 18" (single sensor)
  - Up to 34.5” (dual stacked sensors).
Sensors only work on plastic/polyethylene and fiberglass tanks
Tank senders connect to display via a common bus network topology which saves wiring costs
Uses common industry connector for ease of installation and servicing
RV-C CAN bus interface allows continuous communication with other RV-C compatible systems such as Silver Leaf and Firefly
Alarm output for controlling warning devices, pumps, shutoffs, etc.
- Any or all of the tanks can control the alarm
Continuous scanning of tank levels ensures that the alarm and RV-C interface are always current
Built for OEMs using a momentary switch on a latching relay system, so multiple switches can control the same pump without holding the button down.
Display requires 12 volts from the RV battery, the system will function from 11 volts to 16 volts
Current drain is less than 200mA
Panel Dimensions: 4" W x 2.8" H x 1" D
- Required Cutout Size: 3" W x 1.8" H
Includes: (1) Display monitor, (3) tank senders, (1) pigtail and mounting screws
Limited 1 year manufacturer warranty
See our SeeLevel Tank Monitor Comparison Guide to help you choose the right system for your RV.

NOTE: This system will not work on metal tanks.

Garnet 709-RVC-PM SeeLevel II Tank Monitoring System with Alarm

Garnet SeeLevel Tank Monitor Resource Library

Display mounting panel: Black panel, approximately 4” wide by 2.8” high by 1” thick (102mm wide X 71mm high X 25mm deep). Panel screws to wall.

Power requirements: Display requires 12 volts from the RV battery, the system will function from 11 volts to 16 volts. Current drain is less than 200mA.

Wiring: A single two wire conductor required from the display to the senders. All the senders are wired in parallel. 12 V power and ground required for display. Single wire required for LPG sender if sender grounded at tank.

LPG sender: Display will work with an LPG sender resistance of 0-50 ohms to 0-500 ohms. Display shows increasing level as resistance increases. System must be calibrated with the LPG tank full.

Pump switch:(If equipped) The pump switch is rated for a maximum of 7.5 amps. The use of a relay is required if more than 7.5 amps is needed. We recommend using a 7.5 amp fuse inline with the switch.