Professional-grade 5-chamber 12V RV pump with Flow IQ pressure control, outlet check valve, and run-dry capability. Replaces any OEM pump for single or multi-faucet use. Freshwater only. Made in the USA.
The Remco 55REBEL-JRV is the top-of-the-line model in the PowerRV Rebel Series — the maximum-flow 12V configuration delivering 5.3 GPM at 60 PSI. For RV owners who demand the highest output a 12V Rebel pump can offer, with enough volume and pressure to run the shower, multiple sinks, and the toilet simultaneously without any pressure drop, the 55REBEL-JRV is the definitive choice.
Like all Rebel Series pumps, the 55REBEL-JRV features Flow IQ dual pressure control technology — a system that actively dampens switch cycles and eliminates the rapid on/off pulsing and water hammer common with conventional single-pressure-switch designs. The result is noticeably smoother water delivery, quieter operation, and significantly less wear on the pressure switch and motor over time.
Built from American-made components, 100% factory tested, and backed by a fully sealed motor with thermal overload protection, the 55REBEL-JRV is engineered to handle the most demanding duty cycles of full-time RV living, large coach freshwater systems, and marine applications with multiple simultaneous draw points.
Note: All Rebel Series pumps look identical externally. The differences between the 53, 54, and 55 REBEL models are internal — flow rate and pressure control tuning. Verify you have the correct model number before installing.
Top-of-the-line Rebel flow rate — maximum 12V output for large rigs with high simultaneous demand
Dual pressure control dampens switch cycling — smoother flow, less noise, and longer pump life
Prevents backflow from city water connections into the onboard water system
Factory tested dry for 3 continuous hours with no component defects — built for real-world reliability
The 55REBEL-JRV is rated for intermittent duty only. Observe the following runtime guidelines: • Maximum runtime: 30–45 minutes of continuous operation • Required cool-down: 20 minutes off before resuming Normal on-demand RV use — showers, sinks, toilet flushing, and general fixture use — falls comfortably within this cycle. The pump's built-in thermal protection will automatically shut it down if temperatures rise too high, but observing the duty cycle limits ensures long-term reliability and full warranty coverage.
The 55REBEL-JRV is built for freshwater delivery across a wide range of 12V mobile and off-grid systems: RV & Marine: • Travel trailers, fifth wheels, and motorhomes • Marine freshwater systems on boats and houseboats • Direct OEM replacement for single- or multi-faucet RV systems • Full-time RV living with multiple simultaneous draw points Off-Grid & Alternative Energy: • Cabin and off-grid freshwater supply with 12V power • Solar-powered freshwater systems • Alternative energy and remote water delivery setups Freshwater use only. Not for agricultural chemicals, saltwater, or non-potable fluids.
A typical Rebel Series installation takes 1–2 hours. 1. Mount the Pump: Secure to a solid floor or structural surface using the rubber noise-dampening base. Use #10 screws (1.5" long) with washers — tighten until the screw heads just touch the washers without compressing the rubber grommets. 2. Connect Plumbing: Thread the included QTS-556 fittings into your existing ½" MNPT plumbing lines with Teflon tape, then snap the ¾" Quick Attach hoses onto the pump's inlet and outlet ports. 3. Electrical Connection: Connect the pump leads to your 12V DC supply — the heavier 10 AWG pump wiring handles the full 15A load. Install an appropriate fuse as close to the power source as possible. A relay is recommended for most RV installations. 4. Prime & Test: Open a faucet and briefly power the pump to purge air from the lines. The Flow IQ dual pressure control will engage and disengage smoothly. Check all connections for leaks at operating pressure. For wiring diagrams and relay installation guidance, refer to the Rebel Series manual or contact Remco at 1-800-228-2481.
In The Box: • 55REBEL-JRV Rebel Series Pump • (2) QTS-556 ¾" Quick Attach × ½" MNPT Fittings • Noise-dampening rubber mounting base • Owner's Manual NOT Included (May Need Separately): • Inline fuse and fuse holder (rated for 15A+ load) • Relay (recommended for switched circuits) • Teflon thread tape • Additional hose, clamps, or adapters • Inlet strainer / filter (recommended to protect pump) • Accumulator tank is optional — not required or prohibited with this pump
Download the Remco Rebel Series Installation & Owner's Manual (PDF) Download the 55REBEL-JRV Spec Sheet (PDF) Download the Rebel Series Product Flyer (PDF) Technical Support: Remco Industries Phone: 1-800-228-2481 remcoindustries.com
The 55REBEL-JRV is covered by Remco Industries' 1-Year Limited Manufacturer's Warranty from the date of manufacture (or 1 year from date of purchase with proof of purchase). Remco will repair or replace, at their discretion, any unit found defective in materials or workmanship under normal use. Warranty does NOT cover: • Misuse, abuse, misapplication, or external damage • Products altered outside the Remco factory • Normal wear, brush wear (may be limited to 1,000 hours), or appearance • Pumps not compliant with Remco Engineering Standards Warranty returns require a Return Material Authorization (RMA) number from Remco prior to shipping any product back.
All Rebel Series models look identical externally — the differences are internal. Verify your model number before purchasing or installing. All 12V models share the same 5-chamber diaphragm design, Flow IQ dual pressure control, ¾" Quick Attach ports, run-dry capability, outlet check valve, and Made in USA construction.