Home > Lippert Repair Parts > Electric and Hydraulic Slide-Out Parts >

Lippert 256068 2-Room Hydraulic Slide-Out Manifold and Valves Without Mounting Plate

Lippert 256068 2-room hydraulic slide-out manifold and valves assembly without mounting plate for MIRC systems
Lippert 2 Slide-Out Room Manifold And Valves Without Plate
 
: $141.00
Part Number: 256068
Manufacturer: Lippert
NOTE: Ships in 5 to 7 days

Quantity in Stock :10

Free Shipping
Availability: In Stock
Qty:

 
Lippert MIRC Hydraulic Slide-Out OEM Replacement Part Lippert 256068 -- 2-Room Hydraulic Slide-Out Manifold and Valves (Without Plate)

Keep your hydraulic slide-outs operating reliably with this genuine Lippert replacement manifold and valve assembly. Designed specifically for standard MIRC (Multi-Room In-Room Controlled) hydraulic slide-out systems found across a wide range of fifth wheels and travel trailers, the 256068 restores proper hydraulic flow control to two slide-out rooms when your original manifold fails, leaks, or develops faulty valve function.

Direct Replacement for MIRC Hydraulic Slide Systems

The Lippert 256068 manifold assembly controls the hydraulic fluid routing that extends and retracts up to two slide-out rooms. When valves stick, seals fail, or the manifold body cracks, the entire slide system can lose pressure, move unevenly, or refuse to operate altogether. Swapping this assembly restores factory-spec hydraulic control without requiring a full system overhaul.

This assembly ships as the manifold body and valves only. The mounting plate is not included -- your existing plate can be reused if it is undamaged, which keeps replacement cost and labor down on most service calls.

2-Room Valve Control

Dedicated hydraulic valves for each slide-out room allow independent extension and retraction control across both rooms on the manifold circuit.

MIRC System Fitment

Built to match the standard MIRC hydraulic slide-out architecture used by Lippert across many coach brands and model years.

Plate-Ready Design

Mounts to your existing Lippert mounting plate. Reusing the original plate reduces parts cost and simplifies the swap for experienced DIYers.

1-Year Warranty

Backed by Lippert's limited 1-year manufacturer warranty for defects in materials and workmanship.

What Is the MIRC Hydraulic Slide-Out System?

Lippert's MIRC (Multi-Room In-Room Controlled) system uses a centralized hydraulic pump and a manifold block to distribute pressurized fluid to each slide-out room's hydraulic cylinders. The manifold houses the directional control valves that determine whether each room extends, retracts, or holds position. Over time, valve spools wear, O-rings deteriorate from fluid contamination or age, and manifold bodies can develop micro-cracks -- all of which cause sluggish movement, uneven slide travel, or complete loss of function on one or both rooms.

Reuse Your Existing Plate: If the mounting plate on your current manifold is undamaged, it transfers directly to this replacement assembly. Inspect the plate for cracks, stripped threads, and corrosion before reinstalling. A clean plate reuse saves time and avoids sourcing an additional part.

Typical Installation Notes

  • Retract all slide-out rooms fully before beginning any hydraulic manifold service.
  • Relieve system hydraulic pressure before disconnecting any fittings or lines.
  • Label or photograph all hydraulic hose connections before removal -- port labeling on the replacement manifold should match the original, but confirming line routing prevents errors.
  • Use clean hydraulic fluid compatible with your Lippert system (typically AW32 or Dexron III, per your coach's service manual) when topping off after installation.
  • Cycle each room fully in and out at least twice after installation and check all fittings for seepage before returning the coach to service.
Hydraulic Fluid Note: Small amounts of fluid loss are expected when disconnecting lines. Have rags and a catch pan ready. Top off the reservoir after installation and re-check the level after the first full cycle of both rooms.
Maintenance Tip: If your manifold failed due to contaminated hydraulic fluid (dark, cloudy, or metallic fluid), flush and replace the hydraulic fluid in the entire system when installing this manifold. Running fresh components on degraded fluid accelerates wear on the new valves.

What Is and Is Not Included

  • INCLUDED: Manifold body with integrated 2-room directional control valves
  • NOT INCLUDED: Mounting plate (part sold separately or reuse existing)
  • NOT INCLUDED: Hydraulic hoses or fittings
  • NOT INCLUDED: Hydraulic fluid
  • NOT INCLUDED: Mounting hardware
Also Consider: If your mounting plate is damaged or corroded, source the correct Lippert replacement plate separately to complete the installation. Inspect hydraulic hose ends and fittings for wear while the manifold is out of service -- replacing worn hoses at the same time avoids repeat teardowns.

Part Identification

ManufacturerLippert Components
Part Number256068
UPC848150047687
WarrantyLimited 1-Year Manufacturer Warranty

Physical Specifications

Weight1.5 lbs.
Mounting PlateNot included -- reuse existing or purchase separately

System Compatibility

System TypeStandard MIRC hydraulic slide-out
Number of Rooms Served2 slide-out rooms
ApplicationFifth wheels, travel trailers, and motorhomes equipped with Lippert MIRC hydraulic slide-out systems
Valve FunctionDirectional control -- extend, retract, and hold per room

What Is Included

Manifold BodyIncluded
Directional Valves (x2)Included
Mounting PlateNOT included
Hydraulic HosesNOT included
Hydraulic FluidNOT included
Important Information -- Read Before Installing
  • Always retract all slide-out rooms fully and relieve hydraulic system pressure before disconnecting any hydraulic lines or removing the manifold.
  • Mounting plate is NOT included with this assembly. Verify your existing plate is in usable condition before ordering, or source the plate separately.
  • Confirm your coach uses a standard MIRC hydraulic slide-out system before purchasing. This manifold is not intended for electric or rack-and-pinion slide-out systems.
  • Hydraulic fluid will be present in lines when disconnecting -- use a catch pan and appropriate personal protective equipment.
  • Improper installation or failure to properly bleed and top off the hydraulic system can result in incomplete slide travel, uneven room movement, or hydraulic system damage.
  • Weight: 1.5 lbs. -- confirm this matches the assembly you are removing before finalizing the order.


Browse for more RV Accessories in the same category as this item:

Lippert Repair Parts > Electric and Hydraulic Slide-Out Parts
Lippert Repair Parts