Patented bolt-on semi-automatic leveling for 2007–2018 Mercedes Sprinter 3500 Cutaway Class C motorhomes. No frame drilling or welding. 8,000 lb per jack, 13" stroke, stabilizes in ~30 seconds, 145 lbs complete.
The Bigfoot PC-MB2007 Platinum is a purpose-engineered semi-automatic leveling system for 2007–2018 Mercedes Sprinter 3500 Cutaway Class C motorhomes — one of the most chassis-specific designs in Bigfoot's entire lineup. Its patented bolt-on installation requires no drilling or welding to the Sprinter frame, no relocating of the spare tire, and no rerouting of the rear exhaust. The only drilling required is a small amount into the wheel wells for bracket attachment, preserving Mercedes chassis integrity and warranty coverage.
The Platinum's semi-automatic operation delivers the best of both worlds: press a button and all four cylinders automatically extend, make ground contact, and stabilize the entire vehicle in just over 30 seconds — then you take over with the control panel, using a bubble level or leveling device to fine-tune each corner individually or in pairs until perfectly level. This approach gives you automation for the heavy lifting and precision control for final leveling. The system uses a central pump assembly for space efficiency, with a single marine-grade weatherproof power unit mounting outside the vehicle to preserve every cubic inch of storage. Four powder-coated 8,000 lb cylinders with 13" stroke are machined at Quadra's Michigan facility and carry a lifetime warranty. At just 145 lbs complete with all components, the PC-MB2007 is one of the lightest full hydraulic leveling systems available for the Sprinter platform.
Patented bolt-on install — no frame welding, no spare tire relocation, no exhaust rerouting
One press deploys all four jacks to ground contact and stabilizes the vehicle automatically
Fine-tune each corner individually or in pairs using your bubble level or leveling device
Lightweight full hydraulic system — central pump, 4 cylinders, all hardware included
The PC-MB2007 Platinum operates differently from a fully automatic leveling system. Understanding this two-step process is important before purchasing: Step 1 — Automatic Stabilization (Press a Button): Press the deploy button and all four cylinders automatically extend, make ground contact, and stabilize the vehicle. This takes approximately 30 seconds and requires no user involvement. Step 2 — Manual Fine-Leveling (User Controlled): Using a bubble level or leveling device, check the coach's level plane. Then use the control panel to operate cylinders individually or in pairs to raise or lower each corner until perfectly level. The system responds quickly for on-the-fly adjustment. Important — No Inclinometer: This system does NOT have an inclinometer and does NOT automatically read or level to a true level plane. It will not self-level like the AKC-MB2007 fully automatic system. A bubble level or other leveling aid is required for precise final leveling. Tire Behavior During Leveling: The system is designed for operation with rear tires on the ground. Front tires may leave the ground during leveling — this is normal. Rear tires must maintain ground contact while front cylinders are extended.
Compatible Chassis: 2007–2018 Mercedes Sprinter 3500 Cutaway with 170" Long Wheelbase (Chassis year, not RV model year) Compatible Coach Brands (on Sprinter 3500 Cutaway): • Coachmen • Tiffin • Renegade • THOR • Winnebago • Forest River • Jayco • Pleasure-Way • Dynomax • Most other Class C motorhomes on Sprinter 3500 Cutaway Chassis Year vs. RV Model Year: Order based on your chassis build year — not the year your RV was manufactured. A 2020-model-year RV built on a 2018 Sprinter chassis is compatible with this system. Check your door jamb sticker or title for the chassis manufacture date.
Chassis Year Exclusions: • 2019 and Newer Mercedes Sprinter Chassis — see PC-MB2019 system instead Vehicle Type Exclusions: • Mercedes Sprinter Camper Vans (van chassis body style — see Class B systems) • Airstream (all models) • Roadtrek (all models) Wheelbase Exclusion: • Sprinter 3500 models with wheelbase other than 170" Other Notes: • Some vehicle and RV models may require modifications to weld-on brackets, limit switch wires, battery cables, vehicle exhaust, RV plumbing or wiring, sub-floor brackets or joists, storage boxes, or floors due to varied layouts and owner modifications • Remove all existing leveling system frame brackets before installation Not sure if this system fits your specific Sprinter? Call us at 1-866-332-7881 before ordering.
Hydraulic Cylinders: • (4) Powder-Coated Cylinders (8,000 lb Each) • (4) 100 Square Inch Bigfoot Landing Pads Power Unit: • (1) Central Hydraulic Power Unit • (1) Weatherproof Steel Housing • American-Made Marine Pump & Motor Controls: • (1) Platinum Control Monitor/Panel • All-Up Safety Warning System • Individual & Paired Jack Controls • Complete Wiring Harness Mounting Hardware: • Patented Sprinter-Specific Brackets • Wheel Well Mounting Hardware • All Required Fasteners & Hardware Hydraulic Components: • Universal Length Hydraulic Lines • Hydraulic Fittings & Connections • Reservoir (Requires 2 Qts Dexron III ATF) Documentation: • Installation Manual • Wiring Diagrams • Owner's Manual • Warranty InformationDownload the Bigfoot Leveling Systems Installation Manual NOT Included: • 2 Quarts Dexron III ATF Hydraulic Fluid • Bubble Level or Leveling Device
Factory Installation in White Pigeon, Michigan: Quadra Manufacturing (Bigfoot) offers professional Sprinter installation at their facility with these amenities: • Free Overnight Parking • Free 30-Amp Electrical Hookup • Free WiFi Access • Handicap-Accessible Customer Lounge • Handicap-Accessible Restrooms • Pet-Friendly Facilities • Veteran Discounts Available Schedule Factory Installation: 1. Purchase the Bigfoot Class C Installation Package 2. Call Bigfoot at 1-800-752-9815 to schedule Professional installation is recommended. Some individual coach configurations may require modifications — call ahead to discuss your specific Sprinter build.
Both systems are designed for the same 2007–2018 Sprinter 3500 Cutaway chassis with patented bolt-on installation. The key difference is how leveling is completed after the jacks deploy:
Both systems share the same patented bolt-on installation, identical chassis compatibility, and the same 8,000 lb cylinder platform. The Platinum is a great fit for owners who prefer hands-on precision and don't mind checking a bubble level; the AKC-MB2007 is ideal for those who want to press one button and walk away fully leveled. Questions? Call us at 1-866-332-7881.
RV SnapPad BF-7 pads snap permanently onto your Bigfoot landing pads and stay attached during travel. In addition to eliminating pad placement at every site, SnapPads also increase your system's lift height and expand the footpad contact area — added benefits specific to the Sprinter's tighter installation geometry.
Recommended Accessory: RV SnapPad BF-7 Permanent RV Jack Pads (4-Pack) — Model BF7SP4
Quadra Manufacturing (Bigfoot Leveling Systems): Phone: 1-800-752-9815 Installation Scheduling, Sales & Technical Support